Autocar Self Repair Guides

This information is used by the Engine Control Module to control ignition and fuel injectionThe camshaft position sensor senses the retraction of camshaft intake to identify a particular cylinder. The sensor system consists of a rotating part typically a disc as well as a static part the actual sensor.

How They Work Denso

Specific troubleshooting steps will vary depending on the vehicle.

What does the camshaft position sensor do. What does that mean. It is mounted at the end of the Intake Camshaft See Fig. The ECM needs this data to control how much fuel enters the combustion chamber and ignition spark timing to ignite the fuel.

The changing gap causes the magnetic field near the sensor to change. When the Camshaft Timing pin comes close to the sensor head the voltage at the signal wire drops to zero. When a camshaft sensor fails the check engine light will illuminate and a fault code will be stored.

Any time that the signal to the PCM is inconsistent with what the. A camshaft position sensor is an electronic device that does what it suggests monitor the camshaft position and speed and feeds that data to the vehicles engine control module ECM. The crankshaft position sensor CKP relays crankshaft position and engine.

The camshaft position sensor CMP is used to determine the position of the camshafts. You may be inclined the take your car have the best auto repair Chantilly offers but if you like fixing up cars then you can fix this at home. F7TZ-12K073-B Camshaft Position Sensor for Ford 73L Powerstroke F-250F-350 Super DutyE-350 Club WagonEconoline Replace OE F7TZ-12K073-A Motorcraft DU-87 Camshaft Position Sensor YCT CPS Cam Camshaft Position Sensor F4TZ-12K073-C 1876736C91 F7TZ-12K073-B Fits Ford E350 E450 E550 F250 F350 F450 F550 F650 F750 F59 F Super Duty Econoline Excursion.

The camshaft position sensor CPS sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. The PCM then uses this information to control the fuel injectors and on some applications for ignition timing. This is a generic powertrain diagnostic trouble code DTC which means it covers all makesmodels from 1996 and newer.

A camshaft sensor problem will usually trigger the check engine light. On 2 wire Sensor engines the distributor stator or Camshaft Position CMP sensor is a single Hall effect magnetic switch. The camshaft position sensor is used to synchronize fuel injection and as a feedback device for VANOS variable camshaft timing control.

Dan Ferrell author on October 02 2018. The crankshaft position sensor CKP relays crankshaft position and engine. Without this information the engine would not be able to function properly.

From there you can do a diagnostic scan to suss out a camshaft issue but it wont. Camshaft Position Sensor Circuit RangePerformance. What the P0341 code means.

When the engine is running the high and low parts of the teeth cause the gap with the sensor to change. Basically camshaft and crankshaft position sensors work together to show the computer when the conditions are right for intake compression combustion and exhaust. The camshaft position sensor is always located near the camshaft often at the top of the valve cover but it can also be installed from the side of the cylinder head.

The sensor pulses do not correlate to the pulses of the crankshaft sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Common Symptoms of a Faulty Camshaft Position Sensor 1 Check Engine Light Illuminates.

Due to the lack of feedback information to the computer this sensor problem can cause an engine stumble or hesitation. P0341 is an OBD-II generic code that says the engine control module ECM detected the engine camshaft position sensor circuit is not within specifications. It can also cause the engine to run rough while the car is at cruising speed or at idle.

When a cam sensor goes bad it will cause the check engine light to come on and produce a trouble code. Check around the head or valve cover and follow any electrical wires and you will for sure find the camshaft position sensor. The camshaft position sensor CMP is used to determine the position of the camshafts.

When a Crankshaft Camshaft Position Sensor goes BAD your vehicle will not start. The camshaft position sensor senses the piston position. The camshaft position sensor is an electronic device used in gasoline engines to monitor the position or the rotational speed of the camshaft.

The CMP sensor provides the camshaft position information called the CMP signal which is used by the Powertrain Control Module PCM for fuel synchronization. Do you think the camshaft position sensor is the cause of the problem. I have seen faulty sensors cause engine stalling and poor engine drivability.

The purpose of a camshaft position sensor is to determine the position of the camshaft as it relates to the crankshaft. It relays this information to the powertrain control module PCM. The PCM then uses this information to control the fuel injectors and on some applications for ignition timing.

Distributorless ignition systems DIS require a crankshaft position sensor CKP and sometimes also a camshaft position sensor CMP. Camshaft Position Sensor CMP OPERATION. You can see this happens with bad connected or.

This data is then sent to the powertrain control module PCM for use with fuel injector andor ignition system control. It relays this information to the powertrain control module PCM. Symptoms of a Bad Camshaft Sensor.

31 The Electronic Circuit Camshaft Position Sensor Circuit The Camshaft Position Sensor used in Kia Rio 2010 is the hall-effect type. Check for potential DTCs - this usually happens with a bad sensor that affects a lean or rich fuel mixture temperature sensor throttle posistion sensor oxygen sensor. Camshaft Position Sensor B Circuit RangePerformance Bank 1.

P0340 Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. The position location is used by the engine management system also known as ECU ECM to adjust the timing fuel injection and other engine paramenters. The camshaft position sensor gathers information about the vehicles camshaft speed and sends it to the vehicles engine control module ECMThe ECM uses this data to determine the timing of the ignition as well as the timing of the fuel injection that the engine requires.